Check whether the SRT handshake connection is normal and whether there is video image output in the decoder.
Set “name”, “handshake mode” to “listener”, “port number” and “transmission delay” in turn, which are consistent with the vmix configuration.Ĥ. In the kiloview video decoder, add a SRT type video source to receive the SRT stream. (the “use hardware encoder” generally needs to be selected, which can improve the encoding ability)ģ. Click the gear setting button to pop up the “output settings” dialog box, check “enable SRT” and select “type”Ĭonfigure corresponding parameters for “caller”, “hostname”, “port”, “latency”, “passphrase” and “quality”, check “use hardware encoder”, and click “OK” to confirm. The source of “output” selects the video source to be transmitted (if input1 is selected, it is necessary to ensure that input1 has video signal). Pop up the settings menu and select the “outputs / NDI / SRT” option. Click the gear button on the left of “external” at the bottom and select “output / NDI / SRT settings”Ģ. The vMIX process uses its own dedicated insert so does not use up the existing insert point usable for Lexicon, BSS DPR901ii or external processing. After SRT is connected correctly, vmix can receive and display the video image transmitted by encoder normally.Ģ、 Vmix pushes the SRT stream to the decoder in caller modeġ. The vMIX processing takes the form of a virtual processing block which can be inserted in each input channel that automated mixing is required on. Configure the kilo view encoder as the caller to initiate SRT connection, and then configure the parameters such as “handshake mode”, “IP address”, “port” and “transmission delay” (the relevant parameters need to be corresponding to the vmix side)ĥ. When there is no video stream input, the window will display a black screen.Ĥ. In the main interface of vmix, you can see that vmix has been monitoring the SRT stream in the input1 window. Select “stream type” as “SRT (listener)”, configure parameters such as “port”, “latency”, “passphrase” (if necessary), and “ decoder delay”, and click “OK” to complete the configuration.ģ. Open the vmix software, click “add input” – “more” in the lower left corner, and select the “stream / SRT” option. These can then be connected to two spare inputs on an ATEM switcher.1、 Vmix receives the SRT stream pushed by encoder in listener modeġ. The Key + Fill outputs will be sent over SDI 1 and SDI 2 (or SDI A / SDI B) respectively. If you use the Blackmagic ATEM (Live production switcher) then check the following info The desktop capture would be the screen with Zoom on it. Next, you can add an input inside of vMix with a desktop capture. All you need to do is enable the external output button and then select vMix as your webcam in Zoom. Premultiplied : Same as Straight except the Fill channel will be "Premultiplied" check with the receiving device documentation to determine which of these options should be selected. Sending your video from vMix into Zoom is probably the easiest part of this setup. Straight: Output two channels over the device, Key + Fill on separate SDI ports. None: No alpha channel, send the video output to the device as normal. When selecting a supported device in External Output settings in vMix, an Alpha Channel dropdown box will appear as shown below: To group together SDI ports 1 and 2 as shown below: When using the Decklink Duo 2 or the Decklink Quad 2, port 1 will need to be configured in the Blackmagic Desktop Video Utility
Vmix external output software#
UltraStudio 4K / 4K Extreme / 4K Extreme 3 / HD Miniįind the card configuration, hardware and software requirements clicking here.Decklink Duo 2 / Quad 2 (see additional configuration steps below).
Vmix external output pro#
Decklink 4K Extreme / Extreme 12G / Pro.
0 kommentar(er)
